ABSTRACT
Background: In order to propose a destination for the bottom ash generated from biomass burning, its morphology, functional groups and mineral phases were studied. Dipyrone has been extensively used as an antipyretic, increased due to cases of COVID-19, and due to excretion by urine, incorrect disposal and industrial effluents has been destined to wastewater, being harmful to human and animal life. The present study proposes using biomass ash for the adsorption of dipyrone. Result(s): The characterization of biomass ash shows a sufficient surface area size for adsorption, and a mainly amorphous structure with some peaks of quartz, calcite and other mineral phases. The results show that the kinetic model which best describes the adsorption is the pseudo-first-order model. The Langmuir model best fits at 25 degreeC, and the Freundlich model best describes the adsorption at 35 and 45 degreeC. The thermodynamic parameters indicated that the process is endothermic with a maximum adsorptive capacity of 65.27 mg g-1. In addition, the adsorption is spontaneous, disordered and chemical. The ionic strength study reveals that the adsorbent is promising for real effluent treatment and there is evidence that electrostatic interaction is not the primary adsorptive mechanism, agreeing with the result obtained from pH testing. The proposed mechanism for dipyrone removal involves hydrogen bonds, pi bonds and electron donor-acceptor complex. Conclusion(s): The results are promising in comparison with recent literature and solve two environmental problems: biomass bottom ash disposal and pharmaceutical removal in aqueous medium. The ash may be regarded as a low-cost and environmentally friendly adsorbent. © 2023 Society of Chemical Industry (SCI).
ABSTRACT
This study presents the results of an experimental campaign on the use of municipal solid waste incinerator bottom ash (MIBA) and fly ash (FA) as precursors for the production of alkali-activated materials. MIBA was subjected to a pre-treatment stage in response to two issues: high metallic aluminum content, which reacts in a high pH solution, releasing hydrogen;and low amorphous content of silica-, aluminum- and calcium-bearing phases, which translates into a limited formation of reaction products. The proposed pre-treatment stage oxidizes most of the metallic aluminum fraction and compensates for the low reactivity of the material via the formation of additional reactants. Different combinations of MIBA and FA were tried—mass-based ratios of 0/100, 25/75, 50/50, 75/25, and 100/0 for MIBA/FA. Two mix designs of the alkaline activator with sodium hydroxide and sodium silicate were evaluated by varying the Na2O/binder and SiO2/Na2O ratios. These mortars were tested in the fresh and hardened state. The results showed that the pre-treatment stage was effective at stabilizing the dimensional variation of MIBA. Despite the lower reactivity of MIBA, mortars with 50/50 of MIBA/FA presented a maximum 28-day compressive strength of 25.2 MPa, higher than the 5.7 MPa of mortars made with MIBA only.
ABSTRACT
To dispose of the medical waste generated during the COVID-19 pandemic, a new type of mobile emergency incinerator (MEI) was used in Huoshenshan Hospital, Wuhan, China, and consequently, it produced a number of medical bottom ashs (MBAs). In this study, the characterization and environmental risk evaluation of these MBAs were conducted to evaluate the disposal effect of this MEI used during the pandemic. Three types of leaching tests, EN 12457-2, TCLP 1311, and HJ/T 299-2007, were compared to investigate the release behaviors of major and trace elements from these MBAs. Lack of detection of COVID-19 in MBAs showed that this mobile emergency incinerator could thoroughly eliminate the COVID-19 virus in medical wastes to avoid secondary transmission. The results indicated that the increasing usage of chlorinated disinfectants and physiological saline solutions resulted in high Cl contents in MBAs. In addition, the increasing usage of polypropylene (PP) products changed the chemical properties and compositions of MBAs, with Ca as the main element. The leachability investigation revealed that the main metals in leachates were Ca, Na and K, and the toxic heavy metals such as Zn, Pb, Cu, and Cr in MBAs were difficult to extract because of the high pH (>12) of these MBAs. This study could provide consultation for the treatment and management of MBAs produced from MEIs dealing with emergent infectious diseases such as COVID-19.